Seven tips for mounting solar on asphalt shingle roofs

Esoalr forever recently held a webinar with roof-mounting professionals from EcoFasten Solar, IronRidge and SunModo. The audio speakers shared lots of finest techniques for mounting and also experiences from the area. Below are ideas used for asphalt shingle roofing systems by Dan Felix, training manager at IronRidge. Sight the whole webinar here, or read ideas for metals roofing systems or tile roof coverings.

1. Consult roofing producers concerning blinking.

IBC 1503-2 states that flashing will be set up to stop dampness entering from penetrations via the roof plane. IBC 1507-2-9 says flashing shall be applied in accordance with this area of the code as well as additionally the asphalt shingle maker’s printed directions. “From that note, it’s clear that an installing service provider ought to determine the exact maker of the roof material on a consumer’s residence as well as ascertain the producer’s website for guidelines on appropriately installing a blinking, both for keeping the guarantee and making certain a waterproof roofing system,” Felix stated.

2. Use top quality flashing.

“There’s now just a substantial quantity of flashings choices where to pick in the solar industry,” Felix stated. “We ought to be paying notification to a couple of key items.” Amongst them are corrosion resistance, structural efficiency, waterproofing and ease of setup. A blinking must be ensured to last the life of a planetary system. Felix advises an item with an elevated platform for the real infiltration location to divert water. When locating the rafter, Extra large flashing can accommodate any errors. Flashing makers must have the ability to give installers with third-party certifications of their items.

3.Shingles with 15- as well as 20-year service warranties are existing as well as fairly slim couple of issues when mounting flashings.

Blinking with elevated add-on points will function well in the low locations of the shingle format, reducing the possibilities of the flashing curling as it’s tightened up (casually understood as the “potato chip impact”). In high factors, additional vast flashing will maintain wind-driven rainfall from obtaining to the raised area of that roof material where an infiltration is located.

4.When applying sealer into a pilot hole, service providers need to utilize the sealant specified by the roofing supplier to maintain warranties.

This info, and also much more, can be found on suppliers’ websites.

5.Make sure the blinking does not extend past the drip side of the shingle as the space below can permit leaves and debris to build up, causing rot as well as mildew.

Mount flashing so that its lower edge straightens with the drip edge of that training course of shingles.

6. Do not disrupt water diversion.

Producers will typically permit flashing to be mounted a little more right into a program of shingles than regular, if required. Yet if a blinking item has an elevated system for accessory, be sure to trim the shingles around the altitude to make sure that it sits flush with the base of the flashing. “You do not want to send water to the top of the system,” Felix said. “That platform is developed right into the item to divert water far from your penetration area.”

7. Stay clear of getting rid of nails from shingles.

IBC 1507-2-7 states that asphalt shingles will have the minimal variety of bolts needed by the supplier. “You’ll discover that there are some flashing makers that suggest getting rid of nails or fasteners in the means of your installment,” Felix said. “As an installer, I don’t advise that.” Roof covering installers typically utilize the minimum variety of nails required. Felix advises rocking the flashing to and fro versus the nail to establish the straight area of the nail. Then taking a pair of tin snips, thoroughly cut the smallest V-notch required in the flashing to put it correctly right into the training course of shingles.

IBC 1507-2-9 says flashing will be used in accordance with this area of the code as well as also the asphalt shingle manufacturer’s printed directions. Blinking with elevated accessory points will function well in the reduced locations of the shingle format, reducing the possibilities of the flashing curling as it’s tightened up (casually recognized as the “potato chip result”). Set up blinking so that its bottom side straightens with the drip edge of that program of shingles.

Manufacturers will certainly commonly enable blinking to be set up a little additional right into a training course of shingles than typical, if needed. If a flashing item has a raised platform for add-on, be sure to trim the shingles around the altitude so that it rests flush with the base of the blinking.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top